Products
LI-COR (HOBO, InTemp, LI-COR) · AC-SENS-1
An AC power adapter that provides DC power to sensors that require it, expanding the range of 3rd-party sensors that can be used with Onset's HOBO RX3000, U12, U30-NRC, and ZW series products. Input: 100-240VAC @ 50/60Hz 0.2A Output: 12VDC @ 0.5A
LI-COR (HOBO, InTemp, LI-COR) · 8250-770
Weatherized AC power supply for the LI-8250 Multiplexer. Compatible with 85 to 264 VAC, 50 - 60 Hz power. Provides output of 100 W at 12 VDC (8.33 A max). Power cords are available for outlet types of different regions.
LI-COR (HOBO, InTemp, LI-COR) · AC-U30-EU
AC Battery Charger - rated for 240V, 50Hz input power
LI-COR (HOBO, InTemp, LI-COR) · 6568-566
Advanced polymer gasket for use with the 2 cm2 aperture of the 6800-01A Leaf Chamber Fluorometer. Will also fit the LI-6400 6400-40 Leaf Chamber Fluorometer. Sold individually. White used for both upper and lower apertures.
LI-COR (HOBO, InTemp, LI-COR) · 6568-512
Advanced polymer gasket for use with the 6 cm2 aperture of the 6800-01A Leaf Chamber Fluorometer. Sold individually. Used for both upper and lower apertures.
LI-COR (HOBO, InTemp, LI-COR) · 9978-234
Filter kit for LI-COR's Trace Gas Analyzers. Includes 10 PTFE filters.
LI-COR (HOBO, InTemp, LI-COR) · 286-04198
Used in LI-6400XT, LI-7000 and LI-8100(A). Suitable also for LI-820 or LI-840A analyzers also if flow is regulated down to less than 1L/min, e.g. by an additional needle valve.
LI-COR (HOBO, InTemp, LI-COR) · 9975-026
LI-7550 Air Temperature Sensor. Used with LI-7500A/RS.
LI-COR (HOBO, InTemp, LI-COR) · 9967-008
For use with the LI-8XX CO2/H2O Analyzers, LI-7000 Closed Path CO2/H2O Analyzer as well as discontinued analyzers LI-6262, LI-6252 and LI-6251. One micrometer pore size.
LI-COR (HOBO, InTemp, LI-COR) · 7900-340
To mount an LI-7500A or LI-7200 analyzer; Includes Crossover Fitting, Swivel Mount and Riser Bar
LI-COR (HOBO, InTemp, LI-COR) · W-GUARD-2
This copper guard prevents biofouling of sensors that are attached to MX800 Series Bluetooth water data loggers using the two-sensor adapter and its included sensor guard. This accessory helps to extend the time between sensor cleanings by slowing the growth…
LI-COR (HOBO, InTemp, LI-COR) · U26-GUARD-2
The Anti-fouling Protective Guard can be used in place of the standard protective guard for protection against fouling during deployment. The anti-fouling guard uses copper windings to reduce bio-fouling, while still allowing good water flow to the sensor.
LI-COR (HOBO, InTemp, LI-COR) · 9931-021
Perforated calibration disk, 10 cm², to calibrate series LI-3000 and LI-3100 leaf area meters.
LI-COR (HOBO, InTemp, LI-COR) · 9968-242
DC power connector with bare leads to power Trace Gas Analyzers or the LI-6800 from an external power supply.
LI-COR (HOBO, InTemp, LI-COR) · LI-6021
Replaces the LI-6020 Battery Charger - allows for charging of a single 6400-03 Battery.
LI-COR (HOBO, InTemp, LI-COR) · 590-11830
Single bay battery charger for use with the 442-11807 lithium ion battery only.
LI-COR (HOBO, InTemp, LI-COR) · 8100-623
Bellows Kit for LI-8100/A 10 CM Survey Chambers
LI-COR (HOBO, InTemp, LI-COR) · 8150-250
Plastic tubing used in various LI-COR instruments. Supplied in a 15-meter roll.
LI-COR (HOBO, InTemp, LI-COR) · 300-01961
Used with the LI-6400XT Portable Photosynthesis System, LI-820 CO2 Analyzer, LI-8100 Analyzer Control Unit, LI-8150-8 Multiplexer, and LI-8150-16 Multiplexer.
LI-COR (HOBO, InTemp, LI-COR) · 2420-BNC
Amplifier options for LI-COR LI-190R, LI-200R, LI-210R Light Sensors with type BL or SZ which terminate with bare leads, as well as BNC termination and SA with BNC termination. These amplifiers convert and amplify the sensor's µA current into a voltage output…
LI-COR (HOBO, InTemp, LI-COR) · 312-00600
Replacement BNC connector for older light sensors
Tell EIC Controls about your application.